{"id":1725,"date":"2015-02-19T19:01:35","date_gmt":"2015-02-20T03:01:35","guid":{"rendered":"http:\/\/www.seabrighthotrods.com\/?p=1725"},"modified":"2015-04-29T13:50:06","modified_gmt":"2015-04-29T21:50:06","slug":"34-ford-coupe-heading-for-the-finish-line","status":"publish","type":"post","link":"http:\/\/www.seabrighthotrods.com\/?p=1725","title":{"rendered":"’34 Ford Coupe: Heading for the Finish Line"},"content":{"rendered":"

It\u2019s been awhile since we posted progress photos of Bill Evans\u2019 coupe. It\u2019s not that we haven\u2019t been busting ass \u2013 we promised Bill delivery this Spring\u00a0\u2013 it\u2019s just that the details on which we’ve been laboring, taken individually, didn\u2019t seem especially newsworthy. Taken together though, they add up to a boatload of work.<\/p>\n

The aluminum hood sides Gary built needed stiffening at the trailing edge so they’d match, and maintain, the contour of the cowl. We started by fabbing a pair of beaded stiffeners and riveting them to the hood sides. Gary then edge-welded the assembly, taking care to maintain the contour.<\/p>\n

\"Hood_1\"<\/a> \"Hood_2\"<\/a> \"Hood_3\"<\/a>\"Hood_5\"<\/a>
\nGary had built a pair of separate, lower side panels to fit around the front struts. These had to be tuned up to accommodate the final shape of the hood sides.<\/p>\n

\"Hood_4\"<\/a><\/p>\n

Bill\u2019s VintageAir system in the coupe includes a defroster, which required a vent to be let into the top of the dash console. Like the hood sides, the dash top has more shape in it than appears to the eye and the installation of this vent turned out to take quite a bit of labor.<\/p>\n

\"Defroster_33\"<\/a> \"Defroster_2\"<\/a> \"Defroster_1\"
\n<\/a><\/p>\n

We finished the aluminum panels in the trunk and Gary fashioned a pair of over-center style supports to hold up the deck lid.<\/p>\n

\"Deck<\/a> \"Deck<\/a> \"Deck<\/a> \"Deck<\/a> \"Deck
\n<\/a><\/p>\n

Bill\u2019s coupe arrived at our shop with a third brake light mounted in a custom recess molded into the deck lid. It looked cool \u2014 but presented a problem when it came to routing the wiring. We’ve tried to keep the trunk clean and simple and we didn\u2019t want any wires hanging loose., so we decided to run them along the edge of the deck lid hinge. We clearanced the top of the hinge where it enters the slot in the aluminum panel, then added \u201ctwo walls and a top\u201d to fashion a channel that directs the wires, unseen, to the electrical panel behind the trunk tin.<\/p>\n

\"Wire<\/a> \"Wire<\/a> \"Wire<\/a> \"Wire
\n<\/a><\/p>\n

The original fiberglass body of Bill\u2019s coupe had been extensively modified, including re-hanging the doors so they hinge at the front, rather than the original suicide-style. Unfortunately, nothing had been done to reinforce the jambs and they\u2019d begun to crack.<\/p>\n

\"Door
\n<\/a><\/p>\n

We built up the backside of the jamb with several layers of fiberglass mat, then fabbed up a pair of plates that tied the jamb to the steel cage inside the body and to the wooden door surround. These plates were bolted through the jamb on the front (you can see the countersunk holes in the photo), and epoxyed to the backside.<\/p>\n

\"Door<\/a> \"Door<\/a> \"Door
\n<\/a><\/p>\n

We then cut back the jambs, filled the countersunk holes, and built it back up with a couple of layers of fiberglass mat. With all the fiberglass reinforcement, plus the new steel tying everything together, these jambs shouldn\u2019t go anywhere.<\/p>\n

\"Door<\/a><\/p>\n

To say we\u2019ve had issues with the Engine Control Module is an understatement. The ECM that arived with the car wasn\u2019t even the correct one for the engine\/trans combo. Our only communication with this unruly box is through an OBDII interface. Instead of face-mounting this OBD socket somewhere on Gary\u2019s beautiful dash console, we decided to hide it inside. I built and mounted a bracket and Gary cut a panel that also provides access to the shifter and VintageAir controls.<\/p>\n

\"Console<\/a> \"Console
\n<\/a><\/p>\n

The grille insert had been custom made, but needed a little dental work. Gary squared it up. The window slots in the reconfigured doors had too much arc in them to ever seal against the car\u2019s flat glass, so I filled and squared them up, too.<\/p>\n

\"Gary<\/a> \"Window
\n<\/a><\/p>\n

The rear end needed a lot of tuning. We clearanced the body to give the four-bars ample room to travel, machined spacers to keep the four-bars from kissing the tires, then replaced the coil-overs to get the fenders up off the tires and soften the ride.<\/p>\n

\"New
\n<\/a><\/p>\n

We\u2019re in the home stretch, but there\u2019s still much to do before the car goes to Bill\u2019s painter in Arizona. We\u2019ll keep you posted.<\/p>\n","protected":false},"excerpt":{"rendered":"

It\u2019s been awhile since we posted progress photos of Bill Evans\u2019 coupe. It\u2019s not that we haven\u2019t been busting ass \u2013 we promised Bill delivery this Spring\u00a0\u2013 it\u2019s just that the details on which we’ve been laboring, taken individually, didn\u2019t seem especially newsworthy. Taken together though, they add up to a boatload of work. The […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"jetpack_post_was_ever_published":false,"_jetpack_newsletter_access":"","_jetpack_dont_email_post_to_subs":false,"_jetpack_newsletter_tier_id":0,"_jetpack_memberships_contains_paywalled_content":false,"_jetpack_memberships_contains_paid_content":false,"footnotes":"","jetpack_publicize_message":"","jetpack_publicize_feature_enabled":true,"jetpack_social_post_already_shared":true,"jetpack_social_options":{"image_generator_settings":{"template":"highway","default_image_id":0,"font":"","enabled":false},"version":2}},"categories":[10],"tags":[],"class_list":["post-1725","post","type-post","status-publish","format-standard","hentry","category-current_projects"],"jetpack_publicize_connections":[],"jetpack_featured_media_url":"","jetpack_sharing_enabled":true,"jetpack_shortlink":"https:\/\/wp.me\/p1I3Pf-rP","jetpack_likes_enabled":true,"jetpack-related-posts":[],"_links":{"self":[{"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=\/wp\/v2\/posts\/1725","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=1725"}],"version-history":[{"count":0,"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=\/wp\/v2\/posts\/1725\/revisions"}],"wp:attachment":[{"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=1725"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=1725"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.seabrighthotrods.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=1725"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}